We serviced a
amana dryer
Near Rochester, New York 14624
Dennis
Job Details:
09/05/2025
Customer thought the temperature in the dryer was getting over 400* It has a range of 120 to 190. I suggested that the high limit thermostat might need to be replaced. The customer doesn't want to put any money into a 25 year old dryer. The call was made to see if it was safe to use.
We serviced a
LG Dryer
Near Pittsford, New York 14534
Cristian
Job Details:
09/05/2025
Cleaned out dryer and did a long vent clean everything working normal now
We serviced a
maytag washer
Near Cheektowaga, New York 14225
Jamie
Job Details:
09/05/2025
Drain pump would work sometimes and other times not tested voltage off board had 120 vac tested at the pump only saw .099 vac max the wire came loose from the plug so readjusted wire made sure it seated good in plug test voltage got 120 through the plug now unit is working
We serviced a
whirlpool washer
Near Rochester, New York 14612
Jose R
Job Details:
09/05/2025
Cx has a bad control board and would need to be replaced
We serviced a
LG range
Near Webster, New York 14580
Chris
Job Details:
09/05/2025
Installed customer supplied LED display module - all digits appear to be working. No warranty on customer supplied parts
We serviced a
Kenmore Dishwasher
Near Rochester, New York 14618
Jose R
Job Details:
09/05/2025
Cx has a bad control board causing the pump to run non stop would if Cx wants to go along with any repair would give us a call
We serviced a
Kitchenaid refrigerator
Near Henrietta, New York 14467
Ray
Job Details:
09/05/2025
Ice and frost in freezer cavity. Melted out frost and cleared drain line. Replaced filter casing. Water dispensed temporarily. Replaced braided input line. Operating normal.
We serviced a
frigidaire stove
Near Rochester, New York 14609
Dave
Job Details:
09/05/2025
Found centerburner knob stripped allowing burner to stay on. Customer is going to order and replace
We serviced a
LG Oven
Near Clarence, New York 14031
Tina
Job Details:
09/05/2025
oven would not get to temp so i tested igniter and it only had 2.4AMPS so a new igniter was installed and had 3.5AMPS and the oven heated to 350? without issues
We serviced a
maytag dryer
Near Fairport, New York 14450
Cristian
Job Details:
09/05/2025
Replace rear wheels pulley and belt will have to come back and replace the blower wheel and jumper wire. With new semi rigid vent.
We serviced a
Maytag dryer
Near Buffalo, New York 14228
Tina
Job Details:
09/05/2025
Tested unit had no heat so tested thermostat the cut off had no continuity so ordering cut off kit asked about dryer vent cleaning the vent runs out underneath the deck so no dryer vent cleaning
9/5 installed cut off kit and dryer is heating and running without issues
We serviced a
samsung dryer
Near Tonawanda Town, New York 14150
Samuel
Job Details:
09/05/2025
The dryer was displaying a tE error code. The thermistor only read 14 ohms, so it was replaced. The fan was cleaned of lint. The dryer was tested and no further problems were seen.
We serviced a
LG washer
Near East Aurora, New York 14052
Sam
Job Details:
09/05/2025
Customer states unit doesn't power on unless they reset power. Verified. Unit needs UI control board, part is no longer available.
We serviced a
Whirlpool dishwasher
Near Rochester, New York 14624
Dave
Job Details:
09/05/2025
Drain pump is open and control only sends 13vac to drain pump. Quoted for pump and control.customer is undecided
We serviced a
whirlpool refrigerator
Near Penfield, New York 14526
Chris
Job Details:
09/05/2025
Refrigerator section was approx 40* at time of arrival. Customer says it stays warmer than set points in both refrigerator and freezer sections.
All sensors test per spec , recommend replacing temp control to see if customer can reach satisfactory temperatures.
If customer still wants unit colder recommend they change setting to 6 or 7
If they want it warmer recommend setting to 3 or 4.
Having a bigger thermometer with digital read out may help customer to see what actual temps are.
Ff section should average between 36*-40*
Freezer should be 0-5*
We serviced a
Ge dishwasher
Near Webster, New York 14580
Chris
Job Details:
09/05/2025
Replaced water level sensor and unit now passes all checks in diag / service mode - ran short cycle and behavior is now normal.
We serviced a
Maytag Washer
Near Churchville, New York 14428
Dave
Job Details:
09/05/2025
Gearcase, actuator, and cam have failed. Customer declined to repair
We serviced a
Maytag washer
Near Fairport, New York 14450
Derek
Job Details:
09/05/2025
Mav408daww washer needs a new belt and the hinge for the lid. I replaced the belt it was glazed over shiny and had small dry cracks in it. It spins well and agitates. It sounds and looks good. I replaced the left lid hinge it was loose and the pin part was broken the lid wasn?t closing properly and now it is.
We serviced a
Maytag dryer
Near Cheektowaga, New York 14225
Jamie
Job Details:
09/05/2025
Customer need dryer maintenance kit we replaced that vacuum the dryer out and replaced the venting as well unit is back up and running
We serviced a
Samsung dryer
Near Rochester, New York 14616
Jose D
Job Details:
09/05/2025
All fuses checked out to be good inside the dryer. I reassemble the dryer, and i also cleaned the moisture sensor. Ran the dryer on time dry, and it's showing a good average fluctuating tempature.
We serviced a
Hot Point (GE) oven
Near Rochester, New York 14620
Ray
Job Details:
09/05/2025
Replaced thermostat. Tested unit with thermocouple. Bake flame cycles normal. Customer concerned unit is running hot based on temperature readout from testing device. Customer will monitor and call back if there are additional issues.
We serviced a
Kenmore Freezer
Near Rochester, New York 14609
Jose D
Job Details:
09/05/2025
I replaced the bi-metall heater bar assembly. Advised to call back if the same issue happends again.
We serviced a
Whirlpool dryer
Near Buffalo, New York 14201
Samuel
Job Details:
09/05/2025
The dryer was tested and and was heating well. The dryer had large build up of lint in the cabinet. The lint was cleaned out, and the dryer was tested again.
We serviced a
Frigidaire Refrigerator
Near Ontario, New York 14519
Chris
Job Details:
09/05/2025
Needs inverter and fan blade estimate is approx 378.00 plus tax would be due on return to repair - no repair at this time
We serviced a
Samsung refrigerator
Near Rochester, New York 14622
Jose D
Job Details:
09/05/2025
The fridge is not making the noise on site. I check behind the evap fan area, and everything checked out to be good. Everything look good near the compressor area also. Possible intermittent fan bearing issue. The oven surface element switch only works when set to 200 degrees. The surface element switch will need to be replaced. That part is NLA.
We serviced a
LG Refrigerator
Near Victor, New York 14564
Derek
Job Details:
09/05/2025
I found a loose connector on the mother board I unplugged and plugged it back in. The ice maker is filling with water now.
We serviced a
samsung dryer
Near Rochester, New York 14609
Dennis
Job Details:
09/05/2025
Dryer has a new maintenance kit installed. It's working properly now.
We serviced a
Whirlpool dryer
Near Rochester, New York 14616
Dave
Job Details:
09/05/2025
Replaced idler and cleaned cabinet
We serviced a
Frigidaire dishwasher
Near Irondequoit, New York 14617
Jose D
Job Details:
09/05/2025
A piece of glass was jamming up the drain pump. I removed the glass, and cleaned up the drain hose where it connects to the garbage disposal. Ran and tested, the dishwasher is now draining properly.
We serviced a
amana washer
Near Rochester, New York 14609
Jose D
Job Details:
09/05/2025
The washer isn't showing any signs of leaking on site. Advised to keep the filter holes on the door boot seal clean, Along with the door, since there is a clear indication or pet hair buildup. Advised to call back if the issue happends again. The dryer venting is clean, and doesn't need any service. The fridge condenser coils where full of debri. I cleaned the coils behind the fridge. Advised to call back if the fridge has the same issue again.
We serviced a
Maytag Washer
Near Rochester, New York 14611
Jamie
Job Details:
09/05/2025
Splines on the basket are gone splines on the transmission are worn out and the agitator as well the mode shifter led up to this being a issue I manually engaged the mode shifter and basket and agitator still were spinning separately the customer stated it started making noise couple a weeks ago at this point customer is gonna replace the unit due to age and cost of the unit
We serviced a
GE, Whirlpool stove, dryer
Near Fairport, New York 14450
Ray
Job Details:
09/05/2025
Oven is overheating on stove top and bake cycle. Hot surface light does not come immediately. No broken wires or observable damage. Input voltage correct. Faulty relay on control board. Will need control board to repair. Customer not continuing with repair. Dryer was noisy during spin. Rubber on rollers was worn away. Replaced rollers, belt, and pulley. Tested for spin and heat, operates normally.
We serviced a
LG range
Near Webster, New York 14580
Chris
Job Details:
09/05/2025
Relaxed bake igniter on convection burner - unit checks ok
We serviced a
Kitchen aid oven
Near Rochester, New York 14616
Jose R
Job Details:
09/05/2025
Cx had the part just needed to install heating bake element ran unit and everything is operating with in specs complete
We serviced a
ge dishwasher
Near Orchard Park, New York 14127
Sam
Job Details:
09/05/2025
Customer states not washing dishes, water not agitating. Verified. During test, unit is not sending water to upper wash arms. Will need board. Unit is 9 years old and customer will replace unit for cost of repair
We serviced a
LG Washer/dishwaser
Near Spencerport, New York 14559
Dennis
Job Details:
09/05/2025
Washers power button isn't responding. Been getting worse over time. Will need a new UI. Dishwasher is working properly. Filling running and draining like it should. Customer will keep an eye on it till her next appt.
Will need to return later today with Jk. Customer had to take her son to an appt. New UI is installed but when I plug the washer sparks shoot from the outlet. Outlet is not tripped but same issue is happening.
We serviced a
WHIRLPOOL OR MAYTAG dryer
Near Rochester, New York 14607
Jose R
Job Details:
09/05/2025
Cx had a bad supporter causing the unit to thump while in operation went ahead and replaced maintenance kit now unit is operating with in specs complete
We serviced a
Whirlpool refrigerator
Near Farmington, New York 14425
Derek
Job Details:
09/05/2025
Needs a new fridge it has a sealed system issue. It also has a defrost issue.
We serviced a
Samsung Oven
Near Irondequoit, New York 14609
Jose D
Job Details:
09/05/2025
The igniter is reading 2.3 amperage on site, which is considered low. The amperage should be atleast at 3.0 amperage. The oven will need a new igniter. I replaced the igniter, ran and tested, the oven now has steady heat, and preheated within 10 minutes.
We serviced a
Samsung refrigerator
Near Buffalo, New York 14226
Tina
Job Details:
09/05/2025
Removed ice buildup and tested freezer evap cover, nothing major wrong. Unit needs freezer gasket replaced
9/5 installed gasket on freezer door. it came folded in half and i molded as best as i could i let customer know it might take a little time for it to sit correctly and to just keep making sure is closed so it takes shape.
We serviced a
GE Upright Freezer
Near Macedon, New York 14502
Cristian
Job Details:
09/05/2025
Compressor issue will need to call ge to confirm warranty on compressor .
We serviced a
Hot Pointe Oven
Near Rochester, New York 14620
Sam
Job Details:
09/04/2025
Customer states no heat. Verified, igniter pulling 2.5 amps. replaced igniter. Tested and working
We serviced a
samsung dishwasher
Near Niagara Falls, New York 14304
Tina
Job Details:
09/04/2025
dishwasher was leaking from front right corner and customer had mentioned hey bought the inner tub seal for me to install so when i looked the old one is was all ripped and the bottom of it was kissing so a new seal was installed but it still leaked. i went to go level it due to it leaning forward but the front feet are both missing so it couldn?t be leveled properly but i took cardboard and used it to level as best as i could and i rAn a few time to make sure it didn?t leak anymore and it did not but i talked to customer to let him know feet are missing and he needs to be car when opening and closing it because if it starts to move a lot again then it was be uneven again.
We serviced a
Kenmore dryer
Near Rochester, New York 14625
Sam
Job Details:
09/04/2025
Customer states no spin. Found belt broken and damage to drum glide and felt. Need to order parts, replaced belt and door switch today
We serviced a
Bosch Dishwasher
Near Rochester, New York 14610
Ray
Job Details:
09/04/2025
Drain pump cycled continuously and unit through E15 (float switch) code. Water accumulated in bottom tray. Leaking at water valve. Replaced valve and tested, fill properly with no leaks. Replaced dampers, tested heavy agitation and high spin function. Components operated normal.
We serviced a
Electrolux Refrigerator
Near Pittsford, New York 14534
Cristian
Job Details:
09/04/2025
Customer we need to purchase a new fridge. Seems like there's a harness issue on this unit.
We serviced a
Frigidaire Refrigerator
Near Rochester, New York 14622
Jose R
Job Details:
09/04/2025
Replaced temp control now unit is operating with in specs complete
We serviced a
GE Oven
Near Pittsford, New York 14534
Derek
Job Details:
09/04/2025
needs temp sensor. Installed new sensor and it threw the code again ordered a new relay board. Installed a new board and tested it got to 350 no problem. Then I ran the temp up to 400 for a good 20 min. It tested good no error.
We serviced a
samsung washer
Near Buffalo, New York 14223
Samuel
Job Details:
09/04/2025
The hot and cold hoses were not turned back on after checking the line filters.
We serviced a
Samsung Washer
Near Buffalo, New York 14223
Samuel
Job Details:
09/04/2025
The washer had a slow drain. The pump filter was full of debris. The debris was cleaned out, and the hose filters were checked.
We serviced a
GE refrigerator
Near Farmington, New York 14425
Derek
Job Details:
09/04/2025
The hose for the water line wasn?t connected properly and was sucking air in and not water. I reconnected the fitting and it?s working. There was ice in the bottom of the freezer. The drain hose was clogged and the water was leaking out the front of the freezer. I cleaned the ice out and blasted the drain hose to clear out the blockage. $500 for a new ice maker and dampener repair.
We serviced a
LG refrigerator
Near Buffalo, New York 14216
Samuel
Job Details:
09/04/2025
A large chunk of ice formed on the right side of the bottom freezer door. The ice prevented the door from closing completely. That caused more ice to form in the freezer. The ice was removed and the door sealed properly. No ice was formed on the bottom or back of the freezer and no water was pooling in the fridge.
We serviced a
N/A N/A
Near Macedon, New York 14502
Derek
Job Details:
09/04/2025
I found the compressor isn?t running. I also found the condenser fan blade had popped of the motor. I put the fridge in diagnostic mode and tried to power up the compressor. I found that there was 120v at the inverter to the compressor but the compressor wasn?t turning on. I suspect the compressor is locked up from over heating due to the fan not cooling the system down. It?s time for a new fridge it?s going to cost more for the repair than a new unit.
We serviced a
Ge dishwasher
Near Clarence Center, New York 14032
Tina
Job Details:
09/04/2025
some water was coming in but it was not filling all the way. i took off pressure sensor and it was d trembly dirty so i put a new one on i also cleaned the filter, turbidity sensor and the drain line. dishwasher is working without issues
We serviced a
fridgedair fridge
Near Buffalo, New York 14221
Tina
Job Details:
09/04/2025
water line had broken off in valve so a new valve and a water line was ordered. water line came attached to the filter assy so that was installed along with the water valve and water is working without any issues
We serviced a
kenmore oven
Near Brockport, New York 14420
Dennis
Job Details:
09/04/2025
Oven won't preheat. Found zero amps at the element. While preheating I checked for voltage at the connector. Had no voltage at the connector. Will need a new control board. Board is no longer available. Tried calling the customer several times without anyone answering.
We serviced a
Samsung washer
Near Rochester, New York 14626
Dave
Job Details:
09/04/2025
Tub bearing has failed. Quoted for rear tub. Customer is undecided
We serviced a
Samsung dryer
Near Fairport, New York 14450
Cristian
Job Details:
09/04/2025
Replace Heating element # tested unit working normal now
We serviced a
LG washer
Near Rochester, New York 14610
Jose R
Job Details:
09/04/2025
The washer is making a noise towards the back left dryer wheel. I adjusted the wheel and the ticking sound went away. advised to call back if the issue happends again.
We serviced a
LG washer
Near Hamburg, New York 14075
Jamie
Job Details:
09/04/2025
The washer is making a noise towards the back left dryer wheel. I adjusted the wheel and the ticking sound went away. advised to call back if the issue happends again.
We serviced a
LG refrigerator
Near Lockport, New York 14094
Tina
Job Details:
09/04/2025
Customer explained the ffe code happened after the door was left open on the freezer but seems to be working now so I went through diagnostic mode check all fans operations everything was working as it should made sure gaskets was sealing and explained to lighten up on the freezer to make sure the door is never blocked from closing there was no frost built up around the door or the back wall of the freezer airflow was also good when I was running diagnostic mode and explained the outlet where the fridge is plugged into did have a crack and was recommended to get replaced
We serviced a
Kitchenaid Dishwasher
Near Rochester, New York 14618
Ray
Job Details:
09/04/2025
put washer in service mode and completed without issues then out a load in and ran it and it went unbalanced. suspension rods are needed but customer declined repair and is going to get a new one.
for the dishwasher there are no errors and it washes and completes all cycles without issues. after a cycle is complete the fan in the door is what the customer hears running not nothing else and when she opens the door it stops and i let her know it?s helps with the circulation inside the dishwasher until the door is opened and it?s unloaded
asked about vent cleaning but house is under 1.5 years old and everything is brand new. let her know it would be around $200 if we came out to do it for them
We serviced a
mayatag dryer
Near Rochester, New York 14612
Dave
Job Details:
09/04/2025
Unit does not start cycle. Checked fuses, all resistance values read true. Relay switch is activated on main controller. Will need motor to repair.
We serviced a
GE dryer
Near Buffalo, New York 14204
Samuel
Job Details:
09/04/2025
Cleaned venting and cabinet. Secured vent collar
We serviced a
samsung washer
Near West Henrietta, New York 14586
Ray
Job Details:
09/04/2025
Tested fill, wash and spin with a small load. No problems were found.
We serviced a
Whirlpool washer
Near Irondequoit, New York 14617
Dave
Job Details:
09/04/2025
Re installed rotor bolt and removed extra unneeded length of dryer venting.
We serviced a
LG dryer
Near Rochester, New York 14610
Sam
Job Details:
09/04/2025
Replaced main board, tested working and heating. Found hole in vent, replaced vent as well
We serviced a
Whirlpool Washer
Near Rochester, New York 14609
Cristian
Job Details:
09/04/2025
Would recommend control board # customer decline repair going to get a new machine.
We serviced a
LG range
Near Webster, New York 14580
Chris
Job Details:
09/04/2025
Replaced bake igniter and checks ok
We serviced a
fridged air fridge
Near Buffalo, New York 14214
Samuel
Job Details:
09/04/2025
The fridge was not getting cold because the compressor was not turning on. The start relay was replaced. The fridge was tested and is now producing cold air.
We serviced a
Maytag Washer
Near Rochester, New York 14624
Dave
Job Details:
09/04/2025
Removed gearcase and tub to retrive necklace.
We serviced a
Frigidaire Refrigerator
Near Penfield, New York 14526
Chris
Job Details:
09/04/2025
Removed defrost drain, cleared and defrosted ice build up - unit now is cooling properly.
May take up to 24 hours to reset to normal temperatures
We serviced a
kenmore refrigerator
Near Buffalo, New York 14215
Jamie
Job Details:
09/04/2025
Customer had a loose outlet where the plug for the fridge was in causing it to not power up explained to customer they need to get their outlet replaced to use that outlet for the fridge and in the mean time use a different plug for the fridge when I got there they had it plugged into a different outlet already so checked and made sure everything was working properly all fans was working compressor was running and is cooling
We serviced a
GE dishwasher
Near Rochester, New York 14609
Cristian
Job Details:
09/04/2025
Will recommend to come back with control board Door switch and drain pump but start off with door switch and display first and see what happens from there. Customer would think about the repair.
We serviced a
Kenmore Oven
Near Buffalo, New York 14219
Jamie
Job Details:
09/04/2025
Oven wasn?t igniting check glow bar had 120 vac going to glow bar but not kicking on replaced glow bar and tested unit multiple times worked every time
We serviced a
Whirlpool washer
Near Rochester, New York 14623
Sam
Job Details:
09/04/2025
Customer states unit leaking. Verified. Tub is cracked, customer will replace unit
We serviced a
GE refrigerator
Near Ontario, New York 14519
Chris
Job Details:
09/04/2025
By customer description of leak appears defrost drain was plugged or frozen over. Customer cleaned and cleared ice build up prior to our arrival . Drain is still clear and free flowing at time of service and unable to find any other leaks.
Ice chute door does not close fully and customer states ice will come out occasionally when no one is pushing ice dispenser. All ice chute door / actuator parts are NLA and we are unable to address or repair that issue.
If leak returns recommend customer leave unit in failed state so we can see what?s causing the issue
We serviced a
Kitchenaid Dishwasher
Near Penfield, New York 14526
Dustin
Job Details:
09/04/2025
Replaced faulty drain pump and tested unit. Operating properly
We serviced a
LG dishwasher
Near North Chili, New York 14514
Dave
Job Details:
09/04/2025
Sink backs up and prevents dishwasher from draining. Running the disposal cleares the drain. Made sure drain hose was looped properly.recomending customer cycle disposal before using the dishwasher.
We serviced a
LG refrigerator
Near Irondequoit, New York 14617
Jose D
Job Details:
09/04/2025
The water shoot that goes to the ice maker was clogged with ice. I removed the ice, ran and tested, the ice maker is working properly now. The ice maker passed the diagnostic test.
We serviced a
Samsung Dryer
Near Webster, New York 14580
Chris
Job Details:
09/04/2025
Unit has been attempted to be repaired by other individuals prior to our arrival. Found either faulty valve coils and/or loose connection to valve . Replaced customer supplied coils and unit is now operational.
Unable to warranty parts and possibly labor as multiple hands have been inside unit .
See notes
We serviced a
Samsung refrigerator
Near Rochester, New York 14626
Dave
Job Details:
09/04/2025
Ice maker will not harvest. Customer was undecided on new ice maker
We serviced a
Ge Dishwasher
Near Pittsford, New York 14534
Sam
Job Details:
09/04/2025
Customer states no display / no power. Verified. Removed UI control and reconnected harness. Unit powered on, applied software update related to issue. Tested OK
We serviced a
Jennair refrigerator
Near Rochester, New York 14618
Jose D
Job Details:
09/04/2025
The freezer is leaking water from the corner. The freezer drain is clogged. I removed the clogg with the steamer, and cleaned out the drain tube. The drain is now clear and working properly.
We serviced a
Samsung Refrigerator
Near Rochester, New York 14621
Jose D
Job Details:
09/04/2025
The door flipper is damaged on site and will need to be replaced.
We serviced a
GE washer
Near Fairport, New York 14450
Cristian
Job Details:
09/04/2025
Washer -recommend to get a new unit tub is leaking and loud jet sounds noise
Did a Fridge-coils clean
We serviced a
GE dishwasher
Near Farmington, New York 14425
Derek
Job Details:
09/04/2025
I replaced the water pressure sensor. It wanted to drain all the time.
We serviced a
Maytag washer
Near Rochester, New York 14618
Dustin
Job Details:
09/04/2025
Replaced faulty drain pump. Ran test cycle and unit operating properly
We serviced a
Kitchen Aid Double Oven
Near Hamlin, New York 14464
Dave
Job Details:
09/04/2025
Replaced open lower bake ignitor
We serviced a
GE DW
Near Rochester, New York 14622
Jose R
Job Details:
09/04/2025
Cx unit needed a software update main hoard and display were miss communicating was able to get the unit to turn back and and operate with in specs complete
We serviced a
LG WASHER/DRYER COMBO
Near Bergen, New York 14416
Dennis
Job Details:
09/04/2025
Customer had a drain pump that had had gone bad. Replaced and it's working properly now.
We serviced a
Samsung Washer
Near Rochester, New York 14610
Ray
Job Details:
09/04/2025
Unit throws UB code during spin cycle. Suspension rod springs were bouncing giving little weight resistance. Replaced suspension rods to stabilize tub. Tested with self-diagnostic. All components operating normally.
We serviced a
LG refrigerator
Near Penfield, New York 14526
Chris
Job Details:
09/04/2025
Cleared defrost drain and defrosted evap pan. Replaced 2 bulbs in ff section
We serviced a
maytag washer
Near Rochester, New York 14616
Jose D
Job Details:
09/03/2025
This is a 1995 model Maytag laundry center. It needs a new bearing and spider gear for the drum the drum bearing is shot. The whole drum is loose inside the unit. The parts are no longer available for this machine. Time for a new unit. Lg or Frigidaire laundry center is recommended. The GE laundry centers have many problems.
We serviced a
Kenmore refrigerator
Near Penfield, New York 14526
Dave
Job Details:
09/03/2025
Frost buildup on left side of freezer. Freezer door not closing properly with air gap. Melted out all frost. Left slide was off track and not aligned with right. Adjusted rail and verified that door shut with no gaps. Tightened freezer handle. Tested ice maker, water was injected into mold.
We serviced a
Whirlpool washer
Near Buffalo, New York 14215
Sam
Job Details:
09/03/2025
Bad bearing and tearing apart outter drum assembly customer is gonna replace the unit
We serviced a
Whirlpool oven
Near Webster, New York 14580
Chris
Job Details:
09/03/2025
Oven was dead tested continuity to thermal fuse had a bad thermal fuse once thermal fuse was put in turned power on unit was alive again but tested bake and broil had no heat so tested voltage and continuity to elements no voltage to elements when turning bake or broil on and no continuity to elements explained to cons of the further repair and he is selling the house so he just wanted the thermal fuse replaced.
We serviced a
N/A N/A
Near Buffalo, New York 14221
Tina
Job Details:
09/03/2025
Replaced open thermal fuse
We serviced a
LG Microwave
Near Perinton, New York 14450
Dustin
Job Details:
09/03/2025
Oven temp was off by approximately 25-30* to hot - calibrated to set temp if issue returns will need new oven electronics.
Microwave needs new UI and harness assembly estimate is approx 185.00 plus tax and shipping due on return to replace. Also grill is cracked and part is 50.11 additional if customer would like replaced as well - no repair at this time
We serviced a
amana fridge
Near Fairport, New York 14450
Derek
Job Details:
09/03/2025
Customer states water does not dispenser. Verified, found switch loose. Zip tied switch to housing, tested and working